How To Remove Seat Belt

Download Article

Download Commodity

Seat belts are one of the near important safety features of a vehicle. However, sometimes obstructions inside the seat chugalug buckle can prevent the device from operating equally intended. Y'all might even need to remove one of the seats to make it easier to access the inside of the buckle! Luckily, rather than spending money to replace your whole seat belt system, it's possible to ready the buckle yourself with merely a few easy steps.

1
Inspect the seat chugalug natural language for deformities. These can cause the seat belt buckle to latch improperly or to release merely with smashing difficulty. The tongue is the silvery shaped part of the buckle with a hole in the middle, also sometimes referred to as the "male" connector.^[1]
- If the seat chugalug tongue is deformed, it will likely need to exist replaced entirely.
two
Wiggle a thin or pointed object in the buckle. An item such as a butter knife volition do nicely. This will hopefully dislodge whatsoever foreign objects that may be inside, and is usually sufficient to restore the buckle to proper working order.^[2]
- Items like paper clips, coins, and even small toys can go lodged inside the buckle, impeding the releasing and latching of the tongue.
Advertisement
3

Remove the female part of the buckle from the side of the seat. This might require removing the forepart seats to proceeds access to the nut and commodities holding the buckle in identify. To remove the nut and bolt, apply a bones socket set and ratchet or a simple wrench.^[iii]
4

Turn the buckle upside down and wiggle a thin or pointed object within. Again, a butter knife would work well. If you're certain there is an object within the buckle, endeavor to shake the buckle every bit you wiggle the pointed object to increase the chances of the obstruction falling out.^[4]
five

Pry the buckle open up if the foreign object remains inside the buckle. Some buckles can be opened by loosening a couple screws. Otherwise, use a flathead screwdriver to forcefulness the buckle open. Exercise circumspection as you open the buckle, as springs and other buckle parts might fly free when you do this.
6

Exam the buckle after removing the foreign object. Push the red button and make sure the springs and other internal mechanisms are operating properly. If the springs are rusty, spray a lubricant like WD-xl on the springs to smoothen the spring action.^[v]
7

Reassemble the seat chugalug buckle. Find the indentation on the plastic cover, every bit this is the side that should point towards the clip. Press the plastic comprehend dorsum onto the buckle, and then bolt the buckle back in identify. If the buckle however won't work, you lot will have to replace it entirely.^[6]

Advertizement

1

Slide the seat as far forward equally it tin go. Near cars accept front seats that are bolted to the floor at the front and rear end of the sliding rails. Past moving the seat forrad, you lot volition expose those bolts so they will be easier to remove.^[vii]
2

Take out the seat chugalug anchorage point with a socket wrench. Seat belt anchorages are often subconscious behind a piece of trim. Lift the seat chugalug portion away, then place the bolt that yous simply removed back in identify so information technology doesn't get lost. ^[eight]
3
Remove the bolts at the back of the sliding rails and tip the seat frontward. Make sure not to over-torque the bolts when you remove them. Disconnect any electrical wires still connected to the seat, then maneuver the seat every bit needed to gain easier access to the seat chugalug buckle.^[9]
- Make sure the ignition is off and the key is removed.
4

Reconnect the electric wires to brainstorm reinstalling the seat. Once more, make certain the ignition is off and the key is removed from the ignition. Otherwise, yous hazard inadvertently electrocuting yourself or damaging your car.^[10]
5
Maneuver the seat back onto the sliding frames and screw in identify. In that location should exist hooks in the front of the seat and two locator pins on the rear that volition drib into place. Push the seat every bit far forward as possible on the rail, and then screw the bolts belonging on the runners dorsum in identify.^[eleven]
- Torque the bolts to 30 newton meters (or 20 pounds per pes). If torqued whatsoever harder, the bolts might be nether too much tension to distribute force properly in the outcome of a crash.^[12]
Ad

Inquire a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Always exercise circumspection when tampering with the safety features of a vehicle, and consult a professional person mechanic if you are uncertain of how condom your seat belt is.
Make sure your car's airbag arrangement won't activate while you lot tinker with the seat belt. In some cars, the seat belt sensor can trigger an airbag to go off, or at to the lowest degree a seat belt warning.^[13]

Nearly This Article

Cheers to all authors for creating a page that has been read 53,495 times.

Did this article help you lot?